shop by Category

Site Information

 Loading... Please wait...

shop by Category

How to Install 6.0 Powerstroke Injector Installation Instructions

Step by step instructions on how to diagnose and replace
2003-2007 6.0 Powerstroke Injectors
 
Do you have a bad injector? Tired of paying someone else to replace injectors for outrageous labor rates? Read on my friend, it is really simple if you have any mechanical ability.
 
First thing first, we need to cover a couple questions we get all the time about 6.0 injectors.
 
Q. How do you know if you have a bad injector(s)?
 
A. You really need some sort of scan tool to determine which one is bad for sure. We suggest Auto Enginuity Ford Bundle for those of you attempting to work on your truck yourself.  It will work on any Powerstroke from 95 to present. So if you get a new truck, you will still be able to use it. (We sell them if you need to buy one.) Once you connect the scan tool, you should be able to figure out which injector is the offender. If you are lucky and the miss is bad enough, the computer will store cylinder contribution code for the bad cylinder. If not, do a KOER (Key On Engine Running) test. The pcm will rev the truck up a little and will tell you which cylinder is not carrying it's weight. You can also do a balance test that will graph the contribution of each cylinder. It is really easy to see the bad one.
 
Q. If I have one bad one, do I have to replace all of them?
 
A. Absolutely not! It is a great suggestion if you are selling injectors or getting paid to install them, but not if you are footing the bill. Just replace the one that is causing the miss. There are no issues at all with a new injector working with old ones or any of the stories your uncle or brother-in-law may tell you. Secondly, once you change an injector, you will see that it can be easily done in a couple of hours. The cost of the injectors vs your own labor time is not worth replacing the other perfectly fine injectors. If another one does happen to fail in the next 6 months, no big deal. Just replace it. No big deal.
 
Q. What kind and where should I buy replacement injectors?
 
A. This is a tough one. We have been through most of the different replacement injectors sold on the market today. To be honest, you will get what you pay for. There are a bunch of "rebuilt" injectors on Ebay and the internet selling in the sub $200 range. We have used many of these injectors and have had varying degrees of success. The biggest problem we have found is that they are not replacing all the internals, only what was causing the injector to fail. Since stiction is such a huge problem with 6.0's, getting a set of injectors that haven't had the spool valves replaced will not cure the cold start issues. Worse, we end up replacing some of these injectors within a year of installing them. We suggest buying the ones we have available that are built by Alliant.  Brand new injectors aren't available any longer from any source. But the Alliant injectors are as close as you can get. They replace all the internals. You are basically getting new injectors. We have had the best luck with this brand curing the rough cold starts and keeping the problem away for as long as the stock injectors did. We have them available in our online store for $225 which is pretty reasonable. They also carry a one year warranty.
 
6.0 Powerstroke Injector Installation
 
On to the install:
 
The only special tools you will need is a torque wrench and long T-40 torx bit. Everything else comes apart with regular tools. First thing first, unhook both batteries for safety.
 
The injectors are located under the valve covers. So remove everything from above them.
 
Driver's side - Drain the coolant and remove the Degas bottle. Remove the back part of the air cleaner box and hose all the way to the turbo. Remove the FICM from above the valve cover.
 
Passenger's side - Remove the intercooler tube. Remove the oil filler neck. (you can put the cap back in the valve cover to keep debris out while you are working) Unhook the red alternator wire from the positive side of the battery along with the glow plug relay plugs and the icp sensor plug. Move this whole harness towards the center of the engine out of your way. Next remove the glow plug relay.
 
Now remove all the valve cover bolts. (12MM) Remove the valve cover and valve cover gasket.
 
Now you will need to remove the high pressure oil rail from on top of the injectors. Start by removing the oil stand pipe. It may come out as a long tube or just the short end. Either way is fine:
 6.0 Powerstroke Injector Location
 
Next remove the high pressure rail. You will need a T30 torx bit for the bolts. Remove them all and lift the rail off. The rail is full of oil, so tip it towards the outside of the truck and let it drain into the engine for a few seconds. Have a drain pan ready to set it in.
 
Remove the harness that connects to the injector from where it comes through the rocker box. Just push on the silver lock to release it from the injector harness. You do not need a special tool to remove the injector harness plug from the rocker box. Just use a 3/4 or 18MM socket to release the snaps:
 
 6.0 Powerstroke Injector Hold Down Bolt
 
Now you will need a long (2") T40 Torx bit to remove the injector. The injector will just come right out as you loosen the bolt:
 
Once the injector is out, make sure the copper washer from around the nozzle came with it. If it still isn't on the injector, fish it out of the hole. Make the sure the injector hole is clean and clear of carbon. Oil the orings on the new injector and put it right in. Make sure you torque the injector hold down bolt to 26 ft/lbs. This is a very important step that most people don't do. Trust me, you have to torque the injector down to prevent problems down the road. Reassemble everything you have taken apart in reverse order. One tip is to fill the oil rail from one of the plugs to help quicken startup. Just fill it up with your regular motor oil. It will take a little less than a quart.
 
After you have everything put back together, you will need to roll the truck a little to get it to start. It may not be a bad idea to throw the battery charger/booster on the truck before you start. We also recommend turning the key on and off about five times to fill the fuel rail back up. Next just roll the engine watching the oil pressure gauge on the dash. Once you see the oil pressure come up, turn off the key. Give the starter a break for thirty seconds or so then turn the key back on. Once the glow plug light goes out, start her up. It should fire right up and run rough for a little bit. Check for leaks and you are ready to go!